----------------------- MS-DOS v6.22 Help: DISKCOMP ------------------------
<Notes> <Examples>                                                   <Index>
----------------------------------------------------------------------------
 
                                  DISKCOMP
 
Compares the contents of two floppy disks.
 
This command performs a track-by-track comparison. DISKCOMP determines the
number of sides and sectors per track to compare based on the format of the
first disk you specify.
 
Syntax
 
    DISKCOMP [drive1: [drive2:]] [/1] [/8]
 
Parameters
 
drive1:
    Specifies the drive containing one of the floppy disks.
 
drive2:
    Specifies the drive containing the other floppy disk.
 
Switches
 
/1
    Compares only the first sides of the disks, even if the disks are
    double-sided and the drives can read double-sided disks.
 
/8
    Compares only the first 8 sectors per track, even if the disks contain 9
    or 15 sectors per track.
 
Related Command
 
For information about comparing two files, see the <FC> command.
 
                                      ***

<Syntax> <Examples>
----------------------------------------------------------------------------
 
                              DISKCOMP--Notes
 
Invalid drive for DISKCOMP
 
The DISKCOMP command works only with floppy disks. You cannot use DISKCOMP
with a hard disk. If you specify a hard disk drive for drive1 or drive2,
DISKCOMP displays the following error message:
 
    Invalid drive specification
    Specified drive does not exist
    or is non-removable
 
DISKCOMP messages
 
If all tracks on the two disks being compared are the same, DISKCOMP
displays the following message:
 
    Compare OK
 
If the tracks are not the same, DISKCOMP displays a message similar to the
following:
 
    Compare error on
    side 1, track 2
 
When DISKCOMP completes the comparison, it displays the following message:
 
    Compare another diskette (Y/N)?
 
If you press Y, DISKCOMP prompts you to insert disks for the next
comparison. If you press N, DISKCOMP stops the comparison.
 
DISKCOMP ignores a disk's volume number when it makes the comparison.
 
Omitting drive parameters
 
If you omit the drive2 parameter, DISKCOMP uses the current drive for
drive2. If you omit both drive parameters, DISKCOMP uses the current drive
for both. If the current drive is the same as drive1, DISKCOMP prompts you
to swap disks as necessary.
 
Using one drive for the comparison
 
If you specify the same floppy disk drive for drive1 and drive2, DISKCOMP
does a comparison by using one drive and prompts you to insert the disks as
necessary. You might have to swap the disks more than once, depending on the
capacity of the disks and the amount of available memory.
 
Comparing different types of disks
 
DISKCOMP cannot compare a single-sided disk with a double-sided disk or a
high-density disk with a double-density disk. If the disk in drive1 is not
of the same type as the disk in drive2, DISKCOMP displays the following
message:
 
    Drive types or diskette types not compatible
 
Using DISKCOMP with networks and redirected drives
 
DISKCOMP does not work on a network drive or on a drive created or affected
by a SUBST command. If you attempt to use DISKCOMP with a network drive or a
drive created by the SUBST command, DISKCOMP displays an error message.
 
Comparing an original disk with a copy
 
When you use DISKCOMP with a disk that you made with the COPY command,
DISKCOMP may display a message similar to the following:
 
    Compare error on
    side 0, track 0
 
This type of error can occur even if the files on the disks are identical.
Although the COPY command duplicates information, it doesn't necessarily
place it in the same location on the destination disk. For more information
about comparing individual files on two disks, see the <FC> command.
 
DISKCOMP exit codes
 
The following list shows each exit code and gives a brief description of its
meaning:
 
0
    The disks are the same.
 
1
    Differences were found.
 
2
    The user pressed CTRL+C to stop the process.
 
3
    A critical error occurred.
 
4
    An initialization error occurred.
 
You can use the ERRORLEVEL parameter on the IF command line in a batch
program to process exit codes returned by DISKCOMP. For an example of a
batch program that processes exit codes, see the <CHOICE> command.
 
                                      ***

<Syntax> <Notes>
----------------------------------------------------------------------------
 
                             DISKCOMP--Example
 
If your system has only one floppy disk drive, drive A, and you want to
compare two disks, type the following command:
 
    diskcomp a: a:
 
DISKCOMP prompts you to insert each disk, as required.
 
                                      ***

----------------------------------------------------------------------------
<Top of page>
Last update: June 14, 2000 06:20 EST by -vjf-
Content © 1997 Microsoft Corporation
All else © 2000 Vernon J Frazee
Counter